Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
Here below you'll find some extremely good data on the subject of A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably tough job. If the old tub is conveniently accessible, the project can relocate rapidly; if you have to open a wall surface to remove the old tub and also position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need an assistant to leave the old bathtub and set in the brand-new one. See to it you have actually certified on your own for the work as well as are comfortable attempting it. Rather than employing a contractor to take over a halfway-completed job, it is better to think about using one before you start. Possibilities are you may require an expert plumber to make tube connections.
This post will certainly aid you mount a new bathtub in your bathroom if you have actually already bought a brand-new tub and also don't require to change the arrangement of your previous water pipelines.
Your devices and also material list must consist of the following:
Planning for the Installation
To start with, the sustaining frame provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the tap features a plastic washer, it is fitted between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its last setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome due to the limited access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. When the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the bathtub in the called for setting. The wooden boards are helpful in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 little points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the bathtub till the level reads degree.
To set up faucets, fit the bottom of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait up until the tub has been utilized at least once as this will certainly settle it into its final position.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the other end gives a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap connectors. The former kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom satisfies the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with dampness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your fixtures and installations. They are marketed in tubes and cartridges, and are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the bath tub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can fracture rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily offered on the market. It is suggested to fit the floor tiles using water-resistant or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been introduced to that report about Tools You Need to Install a New Bathtub from a friend on a different web address. Liked our piece? Please share it. Let somebody else locate it. Many thanks for going through it.
Request plumbing analysis. Report this page